spec no: dsal3678 rev no: v.5a date: aug/20/2015 page: 1 of 5 approved: wynec checked: allen liu drawn: m.liu erp: 1203000562 3.0mmx1.0mm right angle infrared emitting diode part number: APA3010F3C-GX features z 3.0mmx2.0mmx1.0mm right angle smd led, 1.0mm thickness. z mechanically and spectrally matched to phototransistor. z package : 2000pcs / reel. z moisture sensitivity level : level 3. z tinned pads for improved solderability. z rohs compliant. description f3 made with gallium arsenide infrared emitting diodes. package dimensions notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.15(0.006") unless otherwise noted. 3. the specifications, characteristics and technical data descri bed in the datasheet are subject to change without prior notice . 4.the device has a single mounting surface. the device must be mounted according to the specifications.
spec no: dsal3678 rev no: v.5a date: aug/20/2015 page: 2 of 5 approved: wynec checked: allen liu drawn: m.liu erp: 1203000562 selection guide notes: 1. 1/2 is the angle from optical centerline where the lumi nous intensity is 1/2 of the optical peak value. 2. radiant intensity / luminous flux: +/-15%. * radiant intensity value is traceable to the cie127-2007 compliant national standards. absolute maximum ratings at ta=25c electrical / optical characteristics at ta=25c note: 1.forward voltage: +/-0.1v. 2.wavelength value is traceable to the cie127-2007 compliant national standards. 3.excess driving current and/or operating temperature higher t han recommended conditions may result in severe light degradation or premature failure. note: 1. 1/100 duty cycle, 10 s pulse width. part no. emitting color (material) lens type po (mw/sr) [2] @ 20ma viewing angle [1] min. typ. 2 1/2 infrared (gaas) water clear 1.2 3 120 *0.8 *2 APA3010F3C-GX parameter p/n symbol typ. max. units test conditions forward voltage [1] f3 v f 1.2 1.6 v i f =20ma reverse current f3 i r 10 ua v r = 5v capacitance f3 c 90 pf v f =0v;f=1mhz peak spectral wavelength f3 p 940 nm i f =20ma spectral bandwidth f3 ? 1/2 50 nm i f =20ma parameter symbol values units power dissipation p d 80 mw dc forward current i f 50 ma peak forward current [1] i fs 1.2 a reverse voltage v r 5 v operating temperature t a -40 to +85 c storage temperature t stg -40 to +85 c
spec no: dsal3678 rev no: v.5a date: aug/20/2015 page: 3 of 5 approved: wynec checked: allen liu drawn: m.liu erp: 1203000562 APA3010F3C-GX
spec no: dsal3678 rev no: v.5a date: aug/20/2015 page: 4 of 5 approved: wynec checked: allen liu drawn: m.liu erp: 1203000562 APA3010F3C-GX recommended soldering pattern (units : mm; tolerance: 0.1) reel dimension tape specifications (units : mm) reflow soldering is recommended and the soldering profile is shown below. other soldering methods are not recommended as they might cause damage to the product.
spec no: dsal3678 rev no: v.5a date: aug/20/2015 page: 5 of 5 approved: wynec checked: allen liu drawn: m.liu erp: 1203000562 packing & label specifications APA3010F3C-GX terms and conditions for the usage of this document 1. the information included in this docum ent reflects representative usage scenarios and is intended for technical reference on ly. 2. the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before production usage customer should refer to the latest datasheet for the updated specifications. 3. when using the products referenced in this document, please make sure the produc t is being operated within the environmental and electrical limits specified in the dat asheet. if customer usage exceeds the spec ified limits, kingbright will not be respon sible for any subsequent issues. 4. the information in this document applies to typical usage in consumer electronics applicati ons. if customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with kingbright representative for further assistance. 5. the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6. all design applications should refer to kingbright application notes available at http://www.kingbrightusa.com/applicationnotes
|
